Do You Have the Proper PPE to Protect From Arc Flash?

Will Your PPE Protect From Electrical Hazards Such as Arc Flash or Arc Blast?

Top 10
Most Frequently Cited OSHA Standards Violated in 2016

  1. Fall Protection
  2. Hazard Communication Standard
  3. Scaffolding
  4. Respiratory Protection
  5. Lockout/Tagout
  6. Powered Industrial Trucks
  7. Ladders
  8. Machinery and Machine Guarding
  9. Electrical – wiring methods
  10. Electrical Systems Design

Source: OSHA.gov

As a certified OSHA Outreach Instructor, a segment I cover in the 10 hour for industry course is Arc Flash & Arc Blast Prevention and Protection. The National Fire Protection Association (NFPA) section 70E regulations state that: anyone exposed to electrical hazards must receive on the job or classroom training in the prevention and protection from arc flash and arc blast hazards every 3 years or, if it is shown through actions that re-training is required.

Many industrial facilities require their electrical workers and facility maintenance workers to take this training annually. Electrical wiring methods, general electrical requirements and lockout/tagout are consistently in OSHA’s top 10 citations. Furthermore, electrical deaths continue to be in OSHA’s Fatal Four for causes of deaths and injuries in the American workplace.

Proper Protection is Key

To begin this segment, I show the students a series of arc flash and arc blast demonstration videos. They show the power, impact, and potential for injury or death should a blast occur. If a student wasn’t paying attention before, they certainly are now. The importance of proper training on arc flash and arc blast cannot be underestimated.

You may be thinking, so if the situation in the video were to happen to me or my workers, how do we protect ourselves? Personal Protective Equipment (PPE) is assigned an arc rating, measured in Cal/cm2.  These Cal ratings are defined by the exposure to arc flash or arc blast. As the combination of voltage and amperage increase, so does the risk of an explosive force.

NFPA 70E then defined 4 hazard risk categories that correlate to arc ratings. Each category from 1-4 has a higher minimum standard for the protective gear that must be worn. As the hazard risk categories increase, so does the level of protection that must be provided by the employer. Hand protection consists of voltage rated gloves and protector. These gloves require mandatory re-inspection every 6 months. Currently, at a minimum, flame resistant attire is mandated when any exposure will exceed 50 volts!

Arc Flash PPE Safety

It is impossible to define the category of exposure from an open circuit panel without doing an arc hazard assessment. This is a calculation that includes the age and condition of the electrical service equipment along with the voltage and amperage.  NFPA regulations require that any non-residential structure have the hazard risk calculation for any electrical exposure, and that the panel or equipment be properly labeled with the energy calculation, PPE required and that the boundary area is clearly marked. The electrical law of physics shows that electricity will pass through the air attempting to find ground. It can pass through human tissue, and can even contain the explosive force of a military hand grenade!

Prevent Exposure to Electrical Hazards

I finish this segment of the training course by covering the various effects of a blast or flash on humans, the best practices for avoiding exposure to the hazard, and some of the recent incidents that have been reported to OSHA. I also emphasize that the key to arc flash prevention is dependent on a complete lockout/tagout program to de-energize any equipment prior to exposure to the electrical hazard. It’s interesting to note that even most licensed, experienced electricians come away from this course with new safety knowledge that they take back with them on the job.

Please reach out if you need your facility maintenance, electrical team or mechanical repair technicians trained or re-trained on these standards. We are here to help!

Are you wearing the proper PPE to protect from electrical hazards at your facility? When was it last inspected?

Stay in touch. Listen in. Better yet, join the conversation.Share on FacebookShare on Google+Tweet about this on TwitterShare on LinkedInEmail this to someone

About the author

Jim Lanz
Jim Lanz

Jim supports our sales team and helps our customers achieve a safe, healthy, and accident-free work environment in his role of Safety Specialist at Horizon Solutions. Jim has over 15 years experience in the field of safety which includes extensive OSHA compliance experience and executing safety programs for manufacturing facilities. Jim is an Authorized OSHA Outreach Instructor, and facilitates safety training classes that involve custom curriculum that meets the specific needs of our customers.